Standard colour white with bootstripe painted with Sikkens polyurethane in choice of red or blue.
All visible exposed hull interiors coated with white polyester flowcoat. Foam-filled FRP interior grid bonded to hull and deck with CSM and woven rovings.Poured flotation foam encapsulated with FRP.
Deck: Composite construction using polyurethane honeycomb or PVC closed-cell foam and FRP construction.
Ashland MaxGuard gelcoat with DSM polyester resin. Hull/Deck joint fastened with mechanical fasteners and 3M 5200 Marine Adhesive or equivalent. Molded non-skid on floor surfaces.
Note: FRP raw materials meet Lloyds, Germanischer Lloyds, BV, or DNV certification for marine use.
Centre Console: Choice of 1) Low console including opening front hatch with lock and gas cylinder, footrest, storage box, opening forward seat with insulated cooler box below, 8mm acrylic windshield and SS windshield frame; 2) Tall console with locking side door, lowered sump, footrest, storage box, opening forward seat with insulated cooler box below, 8mm acrylic windshield and SS windshield frame.
Teak trim: Solid teak step plates in cockpit coaming, bow step, transom steps, dashboard fiddle, and storage shelf rail.
Fuel Tank: 39 U.S. gallon (150 l) stainless steel or 5000-series aluminum to customer specifications. Vent tube with overboard discharge, fuel gauge, and stainless steel deck fill. Optional tank sizes available to customer order.
Engine: Maximum 150hp outboard with 25-inch shaft length.
Steering: Marol hydraulic with console-mounted pump and outboard-mounted cylinder. Sports wheel or
optional laminated teak steering wheel in gloss varnish.
Electrical: 12V system with console-mounted BEP switch plate with integral circuit breakers. Attwood navigation lights to USCG or international standards. Delphi or Varta HD wet-plate battery in molded box and master switch. 750-gph Attwood Sahara bilge pump with mercury float switch.
Hardware: Non-return cockpit drains with overboard drainage, two handholds at rear seats, bow railings, stern handholds, six stainless steel cleats with backing plates, handholds on steering console, cast stainless steel hinges on all seats and opening lockers, forward anchor locker with stainless anchor fitting with roller and cleat, telescoping stainless steel boarding ladder, stainless steel windshield frame with integral handholds. Stainless components of 316 or 316L material and fastened with polished 304 or 316 through-bolts.
Back to top
FEATURES
Effective non-skid on cockpit sole and appropriate seats
Forward anchor locker with overboard drainage
Dual rear anchor/storage lockers under hinged steps
Insulated cooler box under front console seat
Storage under all seats with deep GRP boxes in aft seats
Center cockpit located storage with lift-out box vinyl cushions on all seating areas
Vinyl cushions on all seating areas
Marol hydraulic steering system
Stainless steel bow roller
Solid teak step plates in cockpit coaming, bow step, transom steps
Springfield Marine adjustable helm and passenger seats with fold-up bolster as leaning
posts OR dual fore/aft seats on GRP or SS base
Locking storage in center console
Lockable latches on all or selected seat hatches
Bathing platform ladder
Back to top
OPTIONS
Tall console with accommodation for porta-potty or standard marine toilet with holding tank
Teak cockpit sole with Sika bonding system
Teak steering wheel
Pedestal-mounted FRP cockpit table
Stainless steel fishing rod holders
Hull and bootstripe colors to customer choice
Choice of vinyl cushions colours
Suzuki outboard engine 115 HP/140 HP/150 HP c/w Tachometer, Speedmometer, Fuel Gauge, and Trim Gauge
SS flag mount with teak flag pole
SS T-top frame with GRP cover or customer-supplied fabric
Back to top
